开挖前降水引发基坑变形机制模型试验研究

现有基坑相关研究主要关注土方开挖过程引起的变形，认为围护结构变形起点是土方第1次开挖。然而，一些工程实测表明，基坑开挖前降水阶段即可引起围护结构及周边地层发生厘米级的变形。显然，未考虑开挖前变形的基坑监测数据将低估基坑施工的环境效应。为了研究基坑开挖前降水引发基坑变形的机制，开展了室内模型试验，对基坑开挖前降水过程进行了缩尺精细化模拟。通过微型降水井的设置与调控，模型试验真实再现了实际基坑降水过程中井流效应对围护结构受力变形的影响。试验过程中发现，随着降水的进行，坑外降水漏斗不断扩展，围护结构悬臂式侧移及坑外拱肩式地面沉降也随之产生。另外，降水导致墙前水压力明显减小，并诱发墙前侧向总压力重分布（以减小为主），围护结构为此发生指向坑内的悬臂式运动以寻求新的受力平衡，并通过墙后土体损失诱发坑外地层变形。     

倒置显微镜拍照法对浮游植物计数的稳定性分析

准确定量分析湖泊河流中浮游植物群落结构对评价湖泊河流健康和保障人类饮水安全至关重要.显微镜镜检法是定量分析浮游植物群落结构的唯一方法,但不能满足浮游植物计数分析要求.在Utermhl倒置计数管视野法基础上提出倒置显微镜拍照法,使用拍照法对小球藻、四尾栅藻、斜生栅藻3种纯藻样品和鄱阳湖野外样品计数得到:1)在5、10倍物镜下拍照因浮游植物个体太小导致计数不准确,在20、40倍物镜下拍照计数准确,增加拍照次数可较好地避免计数偏差,拍照次数是影响拍照法计数分析的主要因素; 2)小球藻、四尾栅藻、斜生栅藻在20和40倍物镜下分别拍摄5和10张照片时每升浮游植物计数稳定;鄱阳湖野外样品在20和40物镜倍下分别拍摄5、10张照片时每升浮游植物计数稳定; 3)倒置显微镜拍照法比计数框行格法、目镜视野法、目镜行格法和Utermhl倒置计数管视野法计数稳定,变异系数最小为0.812.     

Variation in the vertical zonality of erodibility and critical shear stress of rill erosion in China's Hengduan Mountains

Soil erodibility is an essential parameter used in soil erosion prediction. This study selected the Liangshan town watershed to quantify variation in the vertical zonality of rill erodibility (k_r) in China's ecologically fragile Hengduan Mountains. Soil types comprised of yellow–brown (soil A), purple (soil B), and dry-red (soil C) in a descending order of occurrence from the summit to the valley, which roughly corresponds to the vertical climate zone (i.e. cool-high mountain, warm-low mountain, and dry-hot valley sections) of the study area. With elevation, vertical soil zonality varied in both soil organic matter (SOM) content and soil particle-size fractions. A series of rill erosion-based scour experiments were conducted, using water discharge rates of 100, 200, 300, 400, 500, and 600 mL min^-1. Additionally, detachment rates (Dr) were measured under three hydrological conditions (the drainage, saturation, and seepage treatments). Results show that both Dr and flow shear stress (Ʈ) values increased as discharge increased. As elevation increased, the k_r values decreased, while the vertical zonality of critical shear stress (Ʈ_c) values showed no obvious variation. The highest k_r values were observed during the seepage treatment, followed by the saturation treatment then drainage treatment, indicating that variation in vertical hydraulic gradients could significantly alter k_r values. This study also found that land-use types could also alter k_r and Ʈ_c values. Further research, however, is necessary to better quantify the effects of subsurface hydrological conditions and land-use types on k_r under different soil zonalities in China's Hengduan Mountains. © 2018 John Wiley & Sons, Ltd.     

Extraction of Lithium from Salt Lake Brine using N523-TBP Mixture System

In this work,problems encountered by tri-butyl phosphate( TBP) in the industrialization of lithium extraction from salt lake brine were discussed in detail. The behavior of N,N-bi-( 2-ethylhexyl) acetamide( N523) during lithium extraction was investigated,and its disadvantages were analyzed in the view of practical application. An N523-TBP mixture extraction system was proposed to alleviate or avoid the defects that N523 and TBP met when they were used separately. The optimal composition of this mixture extraction system was determined to be 20% N523-30% TBP-50% kerosene.The effects of brine acidity,Fe/Li molarity ratio,phase ratio and chloride ion concentration on lithium extraction efficiency were discussed. The operation conditions in single-stage extraction were optimized as brine acidity = 0. 05 mol/L,Fe/Li molarity ratio = 1. 3,and phase ratio = 2. The high concentration of chloride ions in brine was beneficial for the extraction of lithium. The structure of the extracted complex was proposed as( LiFeCl_4·n N523·m TBP)·( 2-n) N523·( 2-m) TBP( m + n = 2) by chemical analysis and slope-fitting methods. The extraction thermodynamic functions were calculated preliminarily,and the results suggested that the extraction process was an exothermic( ΔH 0) and spontaneous( ΔG 0) reaction,and the degree of disorder increased( ΔS 0) during the extraction process. This work will give some guidance to the lithium industry of Qinghai in both the fundamental theory and practical application.     

Morphodynamics of an Artificial Cobble Beach in Tianquan Bay,Xiamen, China

By tracking and monitoring the profile configuration, topography, and hydrodynamic factors of an artificial cobble beach in Tianquan Bay, Xiamen, China over three consecutive years after its completion, we analyzed the evolution of its profile configuration and plane morphology, and its storm response characteristics. The evolution of the profile configuration of the artificial cobble beach in Tianquan Bay can be divided into four stages. The beach was unstable during the initial stage after the beach nourishment the profile configuration changed obviously, and an upper concave composite cobble beach formed gradually, which was characterized by a steep upper part and a gentle lower part. In the second stage, the cobble beach approached dynamic equilibrium with minor changes in the profile configuration. At the third stage the beach was in a high-energy state under the influence of Typhoon Meranti, and the response of the artificial cobble beach differed significantly from that of the low-tide terrace sandy beach. Within a short time, there was net onshore transport of cobbles in the cross-shore direction. The beach face was eroded, the beach berm was accumulated, and the slope of the beach was steepened considerably. In the alongshore direction, there was notable transport of cobbles on the beach from east to west along the shore, and the total volume of the beach decreased by 4.5×103 m~3, which accounted for 50% of the total amount of beach volume lost within three years. The fourth stage was the restoration stage after the typhoon, characterized by a little gentler profile slope and the increase in width and the decrease in height of beach berm. Because of the action of waves and the wave-driven longshore current caused by the specific terrain and landform conditions along the coast(e.g., coastal headlands, near-shore artificial structures, and reefs), the coastline of the artificial cobble beach gradually evolved from being essentially parallel to the artificial coast upon completion to a slightly curved parabolic shape, and three distinct erosion hotspots were formed on the west side of the cape and the artificial drainpipe, and the reefs. Generally, the adoption of cobbles for beach nourishment on this macro-tidal coast beach with severe erosion has yielded excellent stability and adaptability.     

榍石LA-SF-ICP-MS U-Pb定年及对结晶和封闭温度的指示

榍石富含U、Th，贫Pb，是U-Pb定年的理想矿物之一。本文采用激光剥蚀-高分辨等离子体质谱建立榍石U-Pb定年方法，采用25~30μm激光斑束，准确测定榍石U-Pb标准样品BLR-1（~1048Ma）、OLT-1（~1014Ma）和Pakistan（~21.4Ma），以及年轻榍石样品（<100Ma）U-Pb年龄，提高了检测准确性和空间分辨率。综合对比共生锆石和榍石U-Pb年龄、榍石颗粒微量元素和U-Pb年龄环带及不同成分岩浆岩（SiO₂含量48.1%~77.0%）中岩浆榍石的结晶温度，结果表明：岩浆演化过程中，榍石具有宽泛的结晶温度（600~900℃，峰值~750℃），主要集中于岩浆演化中晚期结晶，榍石U-Pb同位素封闭温度接近或略低于锆石，因此同一岩浆体系中锆石与榍石的年龄差异可能反映了该熔体较晚达到榍石饱和，而非熔体热演化历史或封闭温度信息。     

紫外-可见分光光度法测定多花黄精多糖含量

目的：测定湖南洪江国家黄精标准化基地多花黄精中的多糖含量，为多花黄精的进一步开发利用及药材质量标准研究奠定基础。方法：以葡萄糖为标准品，采用硫酸-蒽酮试剂显色，应用紫外-可见分光光度法测定多花黄精多糖含量。结果：葡萄糖在3.28～19.68μg/mL范围内线性良好（r=0.9992），多花黄精多糖平均含量为8.05%。结论：洪江种植基地的多花黄精品质优良，洪江是道地黄精药材种植理想基地。     

顾及地类转换差异的城市空间扩展元胞自动机模型及应用研究

元胞自动机模型已经成为城市空间扩展模拟研究的重要方法之一,并得到广泛应用。然而,现有的城市扩展元胞自动机模型仍存在不足。由于元胞状态设置较为简单,从而使模型转换规则中对不同用地类型向城市用地转换的差异与强度考虑不够。基于此本文在元胞自动机模型的框架下,设计了多元结构的元胞状态及转换规则,提出了顾及地类转换差异与强度的城市扩展元胞自动机模型。在计算非城市用地向城市用地转换的转换概率时,该模型考虑了3个方面的概率：① 地形地貌、经济发展等城市发展的驱动因素对城市用地扩展的影响概率,该概率采用logistics方法进行计算;② 邻域元胞的用地类型对中心元胞转换概率的影响,该概率采用扩展摩尔型方法进行计算;③ 不同类型的非城市用地（本研究中包括耕地、林地和裸地3种类型）向城市用地转换的强度,该概率由模拟基期土地利用数据与目标年份土地利用数据的叠加,得出不同类型的非城市用地在此时间段内向城市用地转换的规模,进而确定不同类型的非城市用地向城市用地转换的强度。最后,将以上3种概率的乘积作为元胞转换的概率。通过转换概率与转换阈值的对比判断中心元胞是否在下一个阶段转换为城市用地。经过迭代计算,不断增加城市用地元胞的数量。当模拟城市用地的结果与目标年份的城市用地规模差值在一定的范围内时停止模拟,得出最终结果。模型构建完成后,本文以长株潭城市群核心区为例进行了模拟实验。以2001年该地区的土地利用数据为基期数据,模拟2010年该地区的城市用地规模和空间分布。研究结果表明,根据本文提出的模型模拟的城市扩展结果与真实数据相比具有较高的一致性。模拟结果正确率达到68.66%,比基于传统logistics回归的元胞自动机模型的模拟精度提高了4.25%,Kappa系数为0.675。该模型较好地模拟了长株潭城市群核心区城市扩展,在城市空间扩展模拟中具有较好的适应性与有效性。     

东太平洋海隆13°N表层含金属沉积物物质组成与元素赋存状态

为了解不同类型含金属沉积物在物质组成和元素赋存状态的差异,对东太平洋海隆13°N洋中脊两侧表层含金属沉积物(站号:E271和E53)进行了矿物学、地球化学分析,顺序提取实验,并与前人对轴部表层沉积物(站号:17A-EPR-TVG1)的研究结果作了对比分析。研究结果表明, E271和E53是远端含金属沉积物,由非浮力热液羽状流中颗粒物沉降所形成的;17A-EPR-TVG1沉积物是近喷口含金属沉积物,由黑烟囱或者热液硫化物丘状体崩塌、堆积,或者由热液羽状流中Fe-Mn氧化物和硫化物快速沉淀而形成的,近喷口沉积物比远端沉积物更富集Fe、Cu和Zn等元素。元素在两种含金属沉积物中的赋存状态基本相同,除了Fe,Cu,Zn,Mo和稀土元素(REE)等元素在远端沉积物中主要存在于Fe-Mn氧化物相,在近喷口沉积物中主要在残留相中。远端沉积物中REE页岩标准化配分模式与海水相似,表明REE主要来自海水,而近喷口沉积物中REE配分模式与热液流体相似,说明REE以高温热液流体来源为主。相关研究结果加深了对热液沉积作用研究的认识。     

海洋功能区划与海洋生态红线关系探讨

海洋生态红线制度是我国"五位一体"文明建设的具体要求。为进一步在自然科学与人文科学的联结点上探求深入开展生态红线工作的可能性,文章对比了实施多年的海洋功能区划与历史新阶段提出的海洋生态保护红线的概念和内涵,剖析了两者之间的区别与联系,指出海洋功能区划与海洋生态红线区划在法律地位和管控制度等方面具有一致性,在划分目标、空间管理及划分方法上具有差异性,海洋功能区划以"使用"为主,海洋生态红线以"保护"引领。在此基础上,建议未来海洋生态红线工作的开展可从海洋功能区划借鉴经验,建立完善的管控评估制度,确立生态保护红线的优先地位,处理好海洋功能区划与海洋生态红线区划的关系。同时,海洋生态红线区划应以维持海洋生态系统结构稳定和提高海洋生态系统服务功能为目标,将区域资源环境承载力评估作为一项参考指标,限制低承载区的开发利用,保证海洋生态环境健康可持续发展。